KAESER KOMPRESSOREN EPC 150-2-G Скачать руководство пользователя

Страница: 64 / 100

7.2 Instructions to be observed before commissioning or re-commis‐

sioning

Incorrect or improper commissioning can cause injury to persons and damage to the machine.
➤ Commissioning may only be carried out by authorized installation and service personnel who

have been trained on this machine.

Special measures for re-commissioning after storage

Storage period

longer than:

Remedy

12 months

➤ Change the compressor oil.
➤ Have the motor bearings checked by an authorized KAESER SERVICE

technician.

36 months

➤ Have the overall technical condition checked by an authorised

KAESER SERVICE technician.

Tab. 31 Re-commissioning after storage

7.3 Checking installation and operating conditions

➤ Check and confirm all the items in the checklist before commissioning the machine.

To be checked

See chapter Confirmed?

➤ Are the operators fully conversant with safety regulations?

–

➤ Have all the positioning conditions been fulfilled?

➤ Is a user-supplied lockable power supply disconnection device in‐

stalled?

6.8

➤ Are the tolerance limits of the mains voltage (power supply) within

the permissible tolerance limits of the nominal voltage (machine)?

2.1 / 2.11

➤ Are the power supply cable conductor diameters and fuse ratings

adequate?

2.11

➤ Have all electrical connections been checked for tightness?
➤ Has the inspection been repeated after 50 operating hours following

the initial commissioning?

–

➤ The supplied air filter

is fitted?

6.4

➤ Is the user's unloading valve

ensuring an unloaded start fitted to

the machine?

6.6

➤ Has the connection to the air system been made with a user's shut-

off valve, check valve and a flexible hose?

6.5

➤ Sufficient oil in the crankcase?

(oil in the sight gauge red zone)

➤ The oil must be changed after 50 operating hours

10.8

➤ Is the user's motor protection device adjusted correctly with regard

to the engine power?

7.4.1

depending on machine

Initial Start-up

7.2

Instructions to be observed before commissioning or re-commissioning

Assembly and operating manual 2-stage piston compressor
EPC-2-G

No.: 9_5753 24 E

Содержание EPC 150-2-G





































































































Результаты поиска

Содержание EPC 150-2-G

Отзывы:

Похожие инструкции для EPC 150-2-G

Бренды по названию

Популярные бренды

KAESER KOMPRESSOREN EPC 150-2-G, Сборка и руководство по эксплуатации

Результаты поиска

Содержание EPC 150-2-G

Отзывы:

Похожие инструкции для EPC 150-2-G

Бренды по названию

Популярные бренды