Juniper QFX5120 Series Скачать руководство пользователя

Страница: 189 / 207

DC Power Electrical Safety Guidelines

•

A DC-powered device is equipped with a DC terminal block that is rated for the power requirements of

a maximally configured device.

Incorporate an easily accessible disconnect device into the facility wiring. Be sure to connect the ground

wire or conduit to a solid office earth ground. A closed loop ring is recommended for terminating the

ground conductor at the ground stud.

•

Run two wires from the circuit breaker box to a source of 48 VDC.

•

A DC-powered device that is equipped with a DC terminal block is intended only for installation in a

restricted-access location. In the United States, a restricted-access area is one in accordance with Articles

110-16, 110-17, and 110-18 of the National Electrical Code ANSI/NFPA 70.

NOTE:

Primary overcurrent protection is provided by the building circuit breaker. This breaker

must protect against excess currents, short circuits, and earth grounding faults in accordance

with NEC ANSI/NFPA 70.

•

Ensure that the polarity of the DC input wiring is correct. Under certain conditions, connections with

reversed polarity might trip the primary circuit breaker or damage the equipment.

•

For personal safety, connect the green and yellow wire to safety (earth) ground at both the device and

the supply side of the DC wiring.

•

The marked input voltage of –48 VDC for a DC-powered device is the nominal voltage associated with

the battery circuit, and any higher voltages are only to be associated with float voltages for the charging

function.

•

Because the device is a positive ground system, you must connect the positive lead to the terminal

labeled RTN, the negative lead to the terminal labeled –48 VDC, and the earth ground to the device

grounding points.

195

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды