Juniper QFX5120 Series Скачать руководство пользователя

Страница: 47 / 207

In data center deployments, position the switch in such a manner that the AIR IN labels on switch

components are next to the cold aisle, and AIR OUT labels on switch components are next to the hot aisle.

QFX5120 Fan Module Status

Each switch has a status LED for each fan module next to the fan module slot on the rear panel of the

chassis. The Status LED indicates the status of the fan module.

Table 7 on page 36

describes the Status

LED on the fan module in an QFX5120 switch.

Table 13: Fan Module Status LED

Description

State

Color

LED

The fan module is functioning normally.

On steadily

Green

Status

An error has been detected in the fan module. Replace the fan

module as soon as possible. Either the fan has failed or it is

seated incorrectly. To maintain proper airflow through the

chassis, leave the fan module installed in the chassis until you

are ready to replace it.

Blinking

Amber

Under normal operating conditions, the fan modules operate at a moderate speed. Temperature sensors

in the chassis monitor the temperature within the chassis.

The system raises an alarm if a fan module fails or if the ambient temperature inside the chassis rises above

the acceptable range. If the temperature inside the chassis rises above the threshold temperature, the

system shuts down automatically.

QFX5120 Power System

IN THIS SECTION

AC Power Supply in QFX5120 Switches | 50

AC Power Supply Specifications for QFX5120 Switches | 52

AC Power Cord Specifications for QFX5120 Switches | 53

AC Power Supply LEDs in QFX5120 Switches | 55

DC Power Supply in QFX5120 Switches | 57

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды