Juniper QFX5120 Series Скачать руководство пользователя

Страница: 10 / 207

About the Documentation

IN THIS SECTION

Documentation and Release Notes | xi

Using the Examples in This Manual | xi

Documentation Conventions | xiii

Documentation Feedback | xvi

Requesting Technical Support | xvi

Use this guide to install hardware and perform initial software configuration, routine maintenance, and

troubleshooting for the QFX5120 switch. After completing the installation and basic configuration

procedures covered in this guide, refer to the Junos OS documentation for information about further

software configuration.

Documentation and Release Notes

To obtain the most current version of all Juniper Networks

technical documentation, see the product

documentation page on the Juniper Networks website at

https://www.juniper.net/documentation/

If the information in the latest release notes differs from the information in the documentation, follow the

product Release Notes.

Juniper Networks Books publishes books by Juniper Networks engineers and subject matter experts.

These books go beyond the technical documentation to explore the nuances of network architecture,

deployment, and administration. The current list can be viewed at

https://www.juniper.net/books

Using the Examples in This Manual

If you want to use the examples in this manual, you can use the load merge or the load merge relative
command. These commands cause the software to merge the incoming configuration into the current

candidate configuration. The example does not become active until you commit the candidate configuration.

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды