Juniper QFX5120 Series Скачать руководство пользователя

Страница: 100 / 207

plant, you can use a multimeter to verify the resistance of the –48V and RTN DC cables to chassis

ground:

•

The cable with very low resistance (indicating a closed circuit) to chassis ground is positive (+) and

will be installed on the V+ (return) DC power input terminal.

•

The cable with very high resistance (indicating an open circuit) to chassis ground is negative (–) and

will be installed on the V– (input) DC power input terminal.

CAUTION:

You must ensure that power connections maintain the proper polarity.

The power source cables might be labeled (+) and (–) to indicate their polarity. There

is no standard color coding for DC power cables. The color coding used by the external

DC power source at your site determines the color coding for the leads on the power

cables that attach to the DC power input terminals on each power supply.

3. Ensure that the input circuit breaker is open so that the voltage across the DC power source cable

leads is 0 V and that the cable leads do not become active while you are connecting DC power.

NOTE:

The V+ terminals are referred to as +RTN, and V– terminals are referred to as –48 V in

“DC Power Wiring Sequence Warning” on page 200

and

“DC Power Electrical Safety Guidelines”

on page 195

4. Ensure that the power supplies are fully inserted in the chassis.

5. Remove the terminal block cover. The terminal block cover is a piece of clear plastic that snaps into

place over the terminal block.

6. Remove the screws on the terminals using the screwdriver. Save the screws.

WARNING:

Ensure that the power cables do not block access to device components

or drape where people can trip on them.

7. Connect each power supply to the power sources. Secure power source cables to the power supplies

by screwing the ring lugs attached to the cables to the appropriate terminals by using the screw from

the terminals.

The QFX5120 is designed to operate with a DC power supply that has a single, non-redundant, feed

input. For source redundancy, two DC power supplies must be installed in the QFX5120; connect

103

Содержание QFX5120 Series
















































































































































































































Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды

Juniper QFX5120 Series, Руководство по оборудованию

Результаты поиска

Содержание QFX5120 Series

Отзывы:

Похожие инструкции для QFX5120 Series

Бренды по названию

Популярные бренды