JUKI AMB-289 Скачать руководство пользователя страница 152

Страница: 152 / 177

– 148 –

10. E396 (Tongue close/open

10-1) Sensor cannot be detected

1-A) Tongue close/open operation

Check close/open of the tongue.

sensor cannot detect) is

or turned OFF when tongue

fails to work.

displayed.

close/open operation is
performed.

1-B) Signal from tongue close/

Check connection or breaking of wire of tongue close/

open sensor does not come.

open sensor and MAIN-INT cord C asm.

1-C) Tongue close/open sensor is

Replace the tongue close/open sensor.

broken.

11. E397 (Chuck close/open

11-1) Chuck close/open sensor

1-A) Button is not set to chuck.

Set a button to the chuck.

sensor cannot detect) is

cannot be detected when

displayed.

sewing machine starts
operation.

1-B) Adjustment of chuck close/

Adjust the chuck close/open sensor.

open sensor is improper.

1-C) Signal from chuck close/

Check connection or breaking of wire of chuck close/open

open sensor does not come.

sensor and NAIN-INT cord C asm.

1-D) Chuck close/open sensor is

Replace the chuck close/open sensor.

broken.

12. E398 (Chuck level sensor

12-1) Sensor cannot be detected

1-A) Adjustment of chuck level

Adjust the chuck level sensor.

cannot detect) is displayed.

at the time of chuck level

sensor is improper

operation

1-B) Signal from chuck level

Check connection or breaking of wire of chuck level

sensor does not come.

sensor and MAIN-INT cord C asm.

1-C) Chuck level sensor is broken.

Replace the chuck level sensor.

13. E399 (Chuck inversion

13-1) Sensor cannot be detected

1-A) Adjustment of chuck

Adjust the chuck inversion sensor.

sensor cannot detect) is

at the time of chuck

inversion sensor is improper.

displayed.

inversion operation.

1-B) Signal from chuck inversion

Check connection or breaking of wire of chuck inversion

sensor does not come.

sensor and MAIN-INT cord C asm.

1-C) Chuck inversion sensor is

Replace the chuck inversion sensor.

broken.

Trouble

Cause (1)

Cause (2)

Inspecting order and adjusting procedure

Содержание AMB-289


















































































































































































Результаты поиска

Содержание AMB-289

Отзывы:

Похожие инструкции для AMB-289

Бренды по названию

Популярные бренды

JUKI AMB-289, Руководство инженера

Результаты поиска

Содержание AMB-289

Отзывы:

Похожие инструкции для AMB-289

Бренды по названию

Популярные бренды