JUKI AMB-289 Скачать руководство пользователя страница 151

Страница: 151 / 177

– 147 –

6. E099 (Loader motor step-out

6-1) Step-out of motor is

1-A) Loader motor stepped out.

Check the loader.

detection error) is displayed.

detected when loader motor
passes origin sensor.

1-B) Signal from loader motor

Check connection or breaking of wire of loader origin

origin sensor does not come.

sensor relay cord asm., loader origin sensor and MAININT
cord C asm.

1-C) Loader origin sensor is broken.

Replace the loader origin sensor.

1-D) MAIN p.c.b. is broken down.

Replace MAIN p.c.b.

7. E303 (Main shaft semilunar

7-1) Semilunar plate sensor of

1-A) Encoder of main shaft motor

Replace the main shaft motor.

plate sensor error) is

main shaft motor is

is broken.

displayed.

abnormal.

7-2) Encoder signal (semilunar

2-A) Connection of connector

Check connection of CN14.

plate) is not inputted.

(CN14) of SDC p.c.b. is
improper.

2-B) Connection of connector

Check connection of CN15.

(CN15) of SDC p.c.b. is
improper.

2-C) Connection of connector

Check connection of CN32.

(CN32) of MAIN p.c.b. is
improper.

8. E394 (Feed plate lowering

8-1) Feed plate lowering sensor

1-A) Feed plate lifting cylinderr

Check lifting of the feed plate.

sensor cannot be detected)

is not detected even when

fails to work.

is displayed.

feed plate lifting solenoid
valve is turned OFF.

1-B) Signal from feed plate lowering

Check connection or breaking of wire of feed plate

sensor does not come.

lowering sensor and MAIN-INT cord C asm.

1-C) Feed plate lowering sensor

Replace the feed plate lowering sensor.

is broken.

9. E395 (Feed plate lifting

9-1) Feed plate lifting sensor is

1-A) Feed plate lifting cylinder

Check lifting of the feed plate.

sensor cannot be detected)

not detected even when feed

fails to work.

is displayed.

plate lifting solenoid valve is
turned ON.

1-B) Signal from feed plate lifting

Check connection or breaking of wire of feed plate lifting

sensor does not come.

sensor and MAIN-INT cord C asm.

1-C) Feed plate lifting sensor is

Replace the feed plate lifting sensor.

broken.

Trouble

Cause (1)

Cause (2)

Inspecting order and adjusting procedure

Содержание AMB-289


















































































































































































Результаты поиска

Содержание AMB-289

Отзывы:

Похожие инструкции для AMB-289

Бренды по названию

Популярные бренды

JUKI AMB-289, Руководство инженера

Результаты поиска

Содержание AMB-289

Отзывы:

Похожие инструкции для AMB-289

Бренды по названию

Популярные бренды