Jntech JNP2K2L-V6 Скачать руководство пользователя страница 9

Страница: 9 / 95

1 Safety Instructions

For the electrical and electronics equipment, safety relates to the whole process of

installation, commissioning, operation and maintenance. Therefore, incorrect use or

operation would damage the life and personal security of operating person or the third

party, and inverters.

In order to reduce casualties, damage of inverter and other equipment, user or operating

person should strictly abide by all the safety information tips of danger, warning and

notice which are in the process of operating and maintaining.

Warning

！

All the installation and operation of Solar Pump Inverter must be done by professional

and technical person. Professional and technical person need:

●

Received special training.

●

Read this manual carefully and know the operation safety matters. Any damage

caused by improper installation or operation will be beyond the warranty scope.

Before installation

Notice

！

User should check the inverter if there is any damage during transportation. Please

contact supplier or transportation company immediately if some problems of inverter are

found.

Installing

Ensure inverter does not have electrical connection with power before installation.

Содержание JNP2K2L-V6
































































































Результаты поиска

Содержание JNP2K2L-V6

Отзывы:

Похожие инструкции для JNP2K2L-V6

Бренды по названию

Популярные бренды

Jntech JNP2K2L-V6, Руководство пользователя

Результаты поиска

Содержание JNP2K2L-V6

Отзывы:

Похожие инструкции для JNP2K2L-V6

Бренды по названию

Популярные бренды