Jntech JNP2K2L-V6 Скачать руководство пользователя страница 3

Страница: 3 / 95

III

Preface

Manual Instruction

This manual describes the trans portation, installation, operation, maintenance

and troubleshooting of the following JNP inverters:

●

JNP2K2L-V6

●

JNP3KL-V6

●

JNP3K7L-V6

●

JNP4KL-V6

For the convenience of the following description

, “JNP2K2L-V6, JNP3KL-V6,

JNP3K7L-V6, JNP4KL-V6

” is short for JNPxL-V6, “Solar Pump Inverter” is

short for inverter in the following content. The inverter model shall be pointed

specially, when introduce the information about each model in details.

Target Reader

This manual applies to the professional engineering and tec hnical person who

is responsible for installing and operating of inverter and LCD panel.

Use the Manual

Please read this manual carefully before installing and operating inverter.

Please keep this manual well for operation and maintenance in future.

The manual content would be constantly updated and revised, but it

unavoidably has slightly discrepancies or errors with real inverter, please kind

prevail if user purchases our inverter.

Symbol Used

The following safety symbols may be used in this manual, and the meanings

Содержание JNP2K2L-V6
































































































Результаты поиска

Содержание JNP2K2L-V6

Отзывы:

Похожие инструкции для JNP2K2L-V6

Бренды по названию

Популярные бренды

Jntech JNP2K2L-V6, Руководство пользователя

Результаты поиска

Содержание JNP2K2L-V6

Отзывы:

Похожие инструкции для JNP2K2L-V6

Бренды по названию

Популярные бренды