Jntech JNP22KH Скачать руководство пользователя страница 9

Страница: 9 / 90

1 Safety Instructions

For the electrical and electronics equipment, safety relates to the whole process of

installation, commissioning, operation and maintenance. Therefore, incorrect use or

operation would damage the life and personal security of operating person or the third

party, and inverters.

In order to reduce casualties, damage of inverter and other equipments, user or

operating person should strictly abide by all the safety information tips of danger,

warning and note which are in the process of operating and maintaining.

Warning

！

All the installation and operation of Solar pumping inverter must be completed by

professional and technical person. Professional and technical person need:

●

Receive special training

●

Read this manual completely and master the operation related to safety matters.

Any damage caused by improper installation or operation which do not

according to the introduction in this manual will be beyond the warranty scope of

our company.

Before installation

Notice

！

User should check the inverter if there is any damage during transportation. Please

contact Supplier or transportation company immediately if some problems of inverter

are found.

Содержание JNP22KH



























































































Результаты поиска

Содержание JNP22KH

Отзывы:

Похожие инструкции для JNP22KH

Бренды по названию

Популярные бренды

Jntech JNP22KH, Руководство пользователя

Результаты поиска

Содержание JNP22KH

Отзывы:

Похожие инструкции для JNP22KH

Бренды по названию

Популярные бренды