Jntech JNP22KH Скачать руководство пользователя страница 48

Страница: 48 / 90

7.4 Motor parameters

’ detection and commissioning

7.4.1 Motor parameters

’ detection

7.4.1.1 Motor parameters

’ detection

After finishing the modification, press

“ENTER” & “DOWN” at the same time to return to

the first screen, long-press

“ON/OFF” for 4S, and inverter begin motor parameters’

detection, if success, it will indicate

“Test finish Start up? YES/NO”; If failed, it will

indicate

” R-Stat Test fail”, then please refer to “

9.1 Trouble Shooting

”, figure 9-1 for

reason.

Pin                  0W
R-Mode     MPPT
Iin                   0A
Vin                  0V
Iaout                0A
Fout          0.00Hz
Run/Stop      Stop
D_Mode       Auto
OF-F               On

Testing...

“

”

r 4

Test finish YES
Start up? NO

YES

Failure

R-Stat
Test fail

Figure 7-1 Motor Parameters

’ Detection Interface

Note

！

In some special occasion, re -detection of motor parameters is required, such as

Содержание JNP22KH



























































































Результаты поиска

Содержание JNP22KH

Отзывы:

Похожие инструкции для JNP22KH

Бренды по названию

Популярные бренды

Jntech JNP22KH, Руководство пользователя

Результаты поиска

Содержание JNP22KH

Отзывы:

Похожие инструкции для JNP22KH

Бренды по названию

Популярные бренды