JLG 3507 Скачать руководство пользователя страница 118

Страница: 118 / 180

116

ASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

ASSEMBLY

FIGURE 23:

3-FUNCTION VERSION ONLY

Fit the sealing rings (34), (36) and the anti-extrusion rings (35),
(37) onto the piston (33) of the service brake.

NOTE:

Carefully check the assembly position of anti-extrusion
rings.

FIGURE 24:

Fit the sealing rings (13), (15) and the anti-extru-

sion rings (14), (16) onto the piston (12) of the negative brake.

NOTE:

Carefully check the assembly position of the anti-extru-
sion rings.

36 37

35 34

36 37

13 14

15 16

FIGURE 25:

Lubricate sealing ring (38) and, using tool T1

(See drawing T1 p. 122), fit it into the cover (8).

NOTE:

Carefully check the direction of ring (38).

FIGURE 26:

3-FUNCTION VERSION ONLY

Measure size "A1" of piston (12) and note it down.

FIGURE 27:

3-FUNCTION VERSION ONLY

Fit the separating ring (10) of Belleville washers onto the cover
(8), measure size "B1" and note it down.

T3 1

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 118 / 180

Результаты поиска

Содержание 3507

Отзывы: