JLG 3507 Скачать руководство пользователя страница 92

Страница: 92 / 180

ASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

ASSEMBLY

FIGURE 9:

Install thrust levers (12) and (13), then install the

U-joint (14).
For details, see DOUBLE U-JOINT p. 29.

FIGURE 10:

Apply Loctite 270 to the threaded portion of the

pins (11) and fit them onto the piston (10).
Block them: torque wrench setting 30 - 35 N·m.

FIGURE 11:

Re-install the piston (10) and the braking disks

(9).
For details, see CHECKING WEAR AND REPLACING THE
BRAKING DISCS p. 19.

12 13

FIGURE 12:

Install the arms (8) into the main body; check flat-

ness and block arms following the appropriate procedures il-
lustrated in section MECHANICAL PARKING BRAKE p. 87
and HYDRAULIC NEGATIVE BRAKE p. 151.

FIGURE 13:

Install the bushing (6) complete with o-ring (7)

and block it with screws (5). Tighten screws with a torque
wrench setting of 23.8 - 26.2 N·m.

FIGURE 14:

Install in sequence the lower o-ring (4), the lever

(3) and the washer (2) with the relative o-ring (4).
Block with screw (1) and tighten using a torque wrench set-
ting of 23.8 - 26.2 N·m.

Refer and keep to the positions marked during disassembly.

CAUTION

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 92 / 180

Результаты поиска

Содержание 3507

Отзывы: