JLG 3507 Скачать руководство пользователя страница 64

Страница: 64 / 180

DISASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

DISASSEMBLY

FIGURE 1:

Remove the complete arms.

For details, see CHECKING WEAR AND REPLACING THE
BRAKING DISCS p. 19.

FIGURE 2:

Mark the position of the ring nuts (1). Remove the

capscrews (3) from the ring nuts (1).

FIGURE 3:

Uniformly heat the ring nuts (1) up to a tempera-

ture of 80° C.

FIGURE 4:

Apply tool T1 (See drawing T1 p. 66) and remove

the ring nuts.

NOTE:

Accurately clean the threaded portions on ring nuts of
body and cover.

FIGURE 5:

Remove the capscrews (4) from the middle cover

(5).

FIGURE 6:

Insert a screwdriver in the opposing slots then for-

ce and remove the middle cover (5) and the complete diffe-
rential unit.

NOTE:

Support the pieces using a rod.

T1 3

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 64 / 180

Результаты поиска

Содержание 3507

Отзывы: