JLG 3507 Скачать руководство пользователя страница 156

Страница: 156 / 180

154

DISASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

NOTE:

The o-rings must be replaced each time the unit is disas-
sembled.

FIGURE 12:

Write down their order of assembly and mark

and remove negative piston sign the position.

FIGURE 13:

Slowly introduce low-pressure compressed air

through the connection member for the negative brake, in or-
der to extract the piston (3).

Hold the piston (3) back, as it may be suddenly ejected and
damaged.

CAUTION

FIGURE 14:

Remove brake discs (14) and (15), writing down

direction of assembly.

NOTE:

If disks are not to be replaced, avoid changing their position.

FIGURE 15:

Remove braking discs (16) and shims (24), wri-

ting down direction of assembly.

NOTE:

If disks are not to be replaced, avoid changing their posi-
tion.

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 156 / 180

Результаты поиска

Содержание 3507

Отзывы: