JLG 3507 Скачать руководство пользователя страница 73

Страница: 73 / 180

ASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

ASSEMBLY

FIGURE 13:

Using a surface plate, reset a dial indicator "DG"

and place it on the measurement ring T5 (See drawing T5
p. 79) (with a thickness of 30.2 mm).
Preset the depth gauge to approximately 2 mm.

FIGURE 14:

Bring the internal bearing (9), complete with its

thrust block, under dial indicator.
Determine overall thickness "D" of the bearing checking the
discrepancy between this size and the size of the measure-
ment ring.

Press the thrust block in the center and take several measu-
rements while rotating the thrust block.

T2 4

CAUTION

FIGURE 15:

Partially insert the thrust block of the external be-

aring (13).

FIGURE 16:

Install tension rod T6C (See drawing T6 p. 80),

measurement ring T5 (See drawing T5 p. 79) and front guide
tool T6A (See drawing T6 p. 80) on the thrust block of the ex-
ternal bearing (13).

FIGURE 17:

Connect the tension rod to the press and move

the thrust block of the external bearing (13) into its seat.
Disconnect the press and remove the tension rod.

NOTE:

Before starting the next stage, make sure that the thrust
block has been completely inserted into its seat.

T25A

T25C

T6C

T6A

T25B

T2 4

T25C

T25A

T6B

T6C

T6A

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 73 / 180

Результаты поиска

Содержание 3507

Отзывы: