JLG 3507 Скачать руководство пользователя страница 167

Страница: 167 / 180

DISASSEMBLY

165

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

FIGURE 19:

Heat the ring nut (19) at approx. 80°C.

FIGURE 20:

Engage special wrench T1 (See drawing T1

p. 169) on the ring nut (19) and apply bar-hold T2 (See dra-
wing T2 p. 170) on the pinion (20).

FIGURE 21:

Remove ring nut (19).

T2 9

T3 0

FIGURE 22:

Using a puller, extract pinion (20) complete with

inner bearing (21), spacer (22) and distance washers.

NOTE:

The thrust blocks of the bearings remain in the central
body (11).

FIGURE 23:

Remove the complete pinion (20).

NOTE:

Carefully check and note direction of installation of spa-
cer.

FIGURE 24:

Using a punch and a hammer, extract the snap

ring (25).

NOTE:

Note direction of installation of snap ring (24).

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 167 / 180

Результаты поиска

Содержание 3507

Отзывы: