JLG 3507 Скачать руководство пользователя страница 130

Страница: 130 / 180

128

ASSEMBLY

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

ASSEMBLY

FIGURE 13:

Insert the shim washer (5) and the differential

side gear (6) in the differential carrier (12).

FIGURE 14:

Position the shim washer (8) and the first plane-

tary gear (7).
Hold them in position using bar T3C (See drawing T3 p. 132).

FIGURE 15:

With the help of press tool T3A (See drawing T3

p. 132), position the second planetary gear (7) and the relative
shim washer (8).

T16C

T3C

T16A

T16C

T3A

T3C

FIGURE 16:

Insert tool T1 (See drawing T1 p. 131) between

the two planetary gears (7). Line up the entire unit by pushing
bar T3C (See drawing T3 p. 132) all the way down until press
tool T3A (See drawing T3 p. 132) is ejected.

FIGURE 17:

Lock tool T1 (See drawing T1 p. 131) behind the

planetary gears (7).
After locking, remove bar T3C (See drawing T3 p. 132).

FIGURE 18:

Fit the snap rings (11) onto the pins (9).

T16C

T1 4

T3C

T1 4

Содержание 3507





















































































































































































Результаты поиска

Содержание 3507

Отзывы:

JLG 3507, Дополнительное руководство по ремонту, Страница: 130 / 180

Результаты поиска

Содержание 3507

Отзывы: