manualshive.com logo in svg

JLG 3507, Дополнительное руководство по ремонту, Страница: 9 / 180

Поделиться
Скачать
JLG 3507 Скачать руководство пользователя страница 9

7

Dana Holding Corporation

ASM-0025E - 212 Axle Service Manual

INTRODUCTION

The efficiency and continued operation of mechanical units depend on constant, correct maintenance and also on efficient re-
pair work, should there be a break-down or malfunction. The instructions contained in this manual have been based on a com-
plete overhaul of the unit. However, it is up to the mechanic to decide whether or not it is necessary to assemble only individual 
components, when partial repair work is needed. The manual provides a quick and sure guide which, with the use of photogra-
phs and diagrams illustrating the various phases of the operations, allows accurate work to be performed.All the information 
needed for correct disassembly, checks and assembly of each individual component is set out below. In order to remove the 
differential unit from the vehicle, the manuals provided by the vehicle manufacturer should be consulted. In describing the fol-
lowing operations it is presumed that the unit has already been removed from the vehicle.

IMPORTANT:

 In order to facilitate work and protect both working surfaces and operators, it is advisable to use proper equip-

ment such as: trestles or supporting benches, plastic or copper hammers, appropriate levers, pullers and specific spanners or 
wrenches. Before going on to disassemble the parts and drain the oil, it is best to thoroughly clean the unit, removing any en-
crusted or accumulated grease. 

INTRODUCTORY REMARKS: 

All the disassembled mechanical units should be thoroughly cleaned with appropriate products 

and restored or replaced if damage, wear, cracking or seizing have occurred. In particular, thoroughly check the condition of 
all moving parts (bearings, gears, ring gear and pinion, shafts) and sealing parts (o-rings, oil shields) which are subject to major 
stress and wear. In any case, it is advisable to replace the seals every time a component is overhauled or repaired. During as-
sembly, the sealing rings must be lubricated on the sealing edge. In the case of the ring gear and pinion, replacement of one 
component requires the replacement of the other one. During assembly, the prescribed pre-loading, backlash and torque of 
parts must be maintained.

CLASSIFICATION: 

This manual classifies units according to part numbers. For a correct interpretation, classification is indica-

ted as follows:

XX

…

= up to the part number

…

XX

= from the part number on

When no classification is given, disassembly and assembly operations are the same for all versions.

SPECIFIC EQUIPMENT AND SPARE PARTS:

 The drawings of all specific tools required for maintenance and repair work can 

be found at the end of this manual ; spare parts may be ordered either from the vehicle manufacturer or directly from the Service 
Centers or Authorized Distributors of SPICER.

Содержание 3507





















































































































































































Отзывы:

Нет отзывов