P/N 960-100175R_Rev. 6 {EDP #200824}
© 2016, JAPAN CASH MACHINE CO., LTD.
2 - 4
Section 2
Taiko™ Series Banknote Acceptor
Installation
Table 2-3 lists the various special DIP Switch
settings available for programing the Taiko™ Unit.
Denomination Setting Mode
Perform the Accept/Inhibit setting function for the
Banknote Denomination required based on the
Software requirements of the Specific Country in
which it is being used. The default settings are to
accept all Denominations of the Specific Country.
A
CCEPT
S
ETTING
M
ODE
To establish an “Accept” setting function, perform
the following steps:
1. Remove power from the Taiko™ Unit.
2. Set DIP Switch No.1 and No.6 to
ON
2-12 above).
3. Re-apply Power to the Taiko™ Unit.
4. After the Front Panel LED display flashes White,
set DIP Switch No.1 to the
OFF
position to enter
the Setting Mode.
5. Insert the Banknote Denomination to be accepted
into the Insertion Slot. The setting registered is
correct if the Front Panel LED Display flashes a
light
Blue
Color, and the inserted Banknote is
returned.
6. Insert the next Banknote Denomination to be
accepted until all required values have been
processed, set and accepted.
I
NHIBIT
S
ETTING
M
ODE
To establish an “Inhibit” setting function, perform
the following steps:
1. Remove Power from the Taiko™ Unit.
2. Set DIP Switch No.1, No. 6 and No.7 to
ON
(Fig-
3. Re-apply Power to the Taiko™ Unit.
4. After the Front Panel LED display flashes White,
set DIP Switch No.1 to the
OFF
position to enter
the Setting Mode.
5. Insert the Banknote Denomination to be inhibited
into the Insertion Slot. The setting is registered if
the Front Panel LED display flashes an
Orange
Color, and the inserted Banknote is returned.
6. Insert next Banknote Denomination to be inhib-
ited until all required values have been processed.
The Banknote ‘Accept’ or ‘Inhibit’ programing
operations are now complete.
LED Pattern Setting Mode
The LED Color Pattern Type can be changed
according to user preference. Select between Pat-
tern 1 or Pattern 2, the default setting is Pattern 1.
D
EFINING
P
ATTERN
1
To define a “Pattern 1” (a flashing Color Sequence)
operating function, perform the following steps:
1. Remove Power from the Taiko™ Unit.
2. Set DIP Switch No.1, No.2 and No.7 to
ON
3. Re-apply Power to the Taiko™ Unit.
4. Set DIP Switch No.1 to
OFF
to cause the LED
Display Pattern to emulate “Pattern 1” when
operating.
Table 2-3
Programming DIP Switch Settings
Setting Function SW1 SW2 SW3 SW4 SW5 SW6 SW7 SW8
Denom.
Value
Setting
Mode
Accept
Setting
ON
OFF OFF OFF OFF
ON OFF OFF
Inhibit
Setting
ON
OFF OFF OFF OFF
ON
ON OFF
LED
Pattern
Setting
Mode
Define
Pattern 1 ON
ON
OFF OFF OFF OFF ON OFF
Define
Pattern 2 ON
OFF
ON OFF OFF OFF ON OFF
Encryption Code
Initialization Setting
Mode
ON
ON
ON
ON
ON
ON OFF OFF
Download Mode
*
*. For details concerning Taiko™ Software Download and Adjustment
Modes, refer to “Software Downloading Procedure” on page 6-1 in
Section 6 of this Service Manual.
ON
OFF OFF OFF OFF OFF ON
ON
Adjustment Mode
*
ON
ON
OFF OFF OFF OFF OFF
ON
ON
Figure 2-12
“Accept” Mode DIP Switch Settings
ON
Figure 2-13
Figure 2-13
“Inhibit” Mode DIP Switch Settings
NOTE: The Accept/Reject setting for a Banknote
denomination can be confirmed by observing the
Front Panel LED Color. After an initial operation
is performed, the LED will flash a number of
times equal to the total number of Banknote
denominations processed.
Blue
indicates an
‘Accept’ setting and
Red
indicates a ‘Reject’
setting.
Figure 2-14
Define Pattern 1 DIP Switch Settings
