JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 36

Страница: 36 / 80

FNS-0002-060-EN January 2017 Rev F

Rebuilding (Continued)

4. From 3 inch square access hole on side of machine, use a 5/16" Allen wrench to loosen

socket head cap screw on crank arm for upper cup drive .

(Use hand crank adapter to rotate as necessary).

Use a 3/16" Allen wrench to loosen set screw on keyway. Back screws out at least 1/4" to
clear flats on shafts.

Refer to Figure 22.

From the back repeat above steps on crank arm for lower drive.

Refer to Figure 23.

5. Rotate drive so upper cup drive is in the down position.

Remove chain, spring clip type master link.

Be careful- drive arms may move as chain is removed

6. Remove sprockets with shafts still connected.

Pull or pry on large diameter upper drive sprocket, repeat for lower drive sprocket.

Refer to Figure 24.

Figure 22. Using Allen Wrench to Loosen Upper Cup Crank Arm

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды