JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 12

Страница: 12 / 80

FNS-0002-060-EN January 2017 Rev F

Juicing

CAUTION

NOT

RUN

JUICER

WITHOUT

FRUIT FOR

MORE

THAN

ONE

MINUTE.

EQUIPMENT

DAMAGE MAY RESULT.

Turn

Juicer.

Push the "ON-OFF" button to "ON" position.

Fruit

may

fed

into

Juicer

one

time

(Single

Feed)

or in

bulk.

Single

Feed

Remove hopper single feed hole cover.

Twist and pull cover to remove.
Drop fruit individually down single-feed chute through hole in hopper cover.

DO NOT

overload chute or fruit will accidentally be double fed.

b. Bulk Feed

Unlock and open the hopper cover.
Dump up to one carton (40 Ibs.) of fruit into the hopper.
Fruit may be divided between the carton and carton lid for ease of lifting.

DO NOT use the single-feed chute when hopper is full.

Fruit will accidentally be double fed.

Turn-off Juicer.

Push the "ON-OFF" Switch to the "OFF" position.

Stir juice.

Use stirrer handle to stir juice in reservoir before filling containers.

Fill containers.

Place container under juice reservoir valve. Open valve by turning lever until
container is full.

Clean Juicer.

If finished juicing, clean Juicer as soon as possible.

(See Page 14 for cleaning instructions.)

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды