JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 45

Страница: 45 / 80

FNS-0002-060-EN January 2017 Rev F

Rebuilding (Continued)

16. Before installing chain, align timing marks as shown.

Refer to Figure 36.

This is critical to operation of the machine. Adjust chain as shown in Maintenance section.

17. To check if the upper cup crank rod end link needs to be adjusted, install juice manifold,

upper and lower cup.

Refer to Figure 37.

Using hand crank adapter, gently rotate until upper cup drive is in the full down position.

DO NOT

force, if it appears to be binding, readjust rod end link (

Figure 38

)

If it rotates freely past

bottom position, check for too much clearance. In the full down position, remove pull pin from
upper cup. Cup should not drop down; if it does, readjust rod end link.

Cups should just meet - no clearance - no bind.

Figure 36. Alignment of Timing Marks

ROTATION

Align Marks

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды