JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 13

Страница: 13 / 80

FNS-0002-060-EN January 2017 Rev F

Operator Do's and Don'ts

Do's

Don'ts

Unplug juicer before opening juicing component
door

DO NOT open juicing component door before
unplugging

Stop juicer when cups are in most open position

DO NOT stop juicer when cups are in closed
position

Use light water spray when rinsing juicer

DO NOT use high pressure or volume water when
rinsing juicer

When hopper cleaning, use spray bottle and damp
towel

When hopper cleaning, DO NOT use chemical
dosage and water system

Use spray bottle with cleaner on main frame
casting in juicing components area

DO NOT use chemical dosage and water system
to clean main casting (can result in mechanical
damage)

Rinse sanitizer off juicer five minutes after applying

DO NOT leave sanitizer on juicer without rinsing
(can damage aluminum)

Use fruit within size range (2-1/2" to 3-7/8"
diameter)

DO NOT use oversized fruit

Use fruit within size range (2-1/2" to 3-7/8"
diameter)

DO NOT use small fruit
(can result in double feed and cause cups to break)

Inspect and test safety switches and door locks
weekly

DO NOT use juicer if safety switches are not work
properly

Install juicing components using spanner tool;
tighten spanner nuts and screw from top to bottom

DO NOT hand tighten spanner nuts and screw
(can result in major equipment damage)

Install orifice tube into slot on lower arm
(see Figure 6 on Page 19)

DO NOT install orifice tube on top of lower arm slot
(see Figure 6 on Page 19)

Inspect cutter daily.
Replace if damaged; adjust and tighten screw

If cutter is damaged, loose or dull, juice quality and
yield can be impacted

Mix juice and pulp slowly to reduce foam in
reservoir

DO NOT mix juice quickly in reservoir (can result in
foam and off flavor)

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды