JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 80

background image

10

FNS-0002-060-EN January 2017 Rev F

Operating Instructions

Equipment Check

Before

plugging

the

Multi-Fruit Juicer

into

an

electrical

outlet, the

following

steps

must

be

performed:

1.

Locate

the

Multi-Fruit Juicer

on

a

level

surface.

This will prevent fruit feed problems.

CAUTION

:

WHEN MOVING JUICER, ALWAYS TRANSPORT ON LEVEL SURFACE.
USE RAMPS IF NECESSARY. AVOID LEDGES, IRREGULAR FLOORS
OR DRAIN INDENTIONS.  TO AVOID TIPPING, NEW JUICER UNITS ARE
SHIPPED  WITH BRACING RAILS. UNITS IN THE FIELD CAN BE
UPGRADED USING THE BRACING RAIL KIT.
SEE FIGURE 5 FOR INSTALLATION INFORMATION.

2.

Lock both rear casters.

To lock, push down on caster with foot. To unlock, push again with foot.

3.

Check waste container.

Open cart door to verify that waste container is in place. A plastic bag may be

attached to the hooks above the waste container (30 gallon capacity or equivalent).

4. Check juicing components.

a. Twist and pull juice nozzle off.

b. Use key to unlock juicing components cover. Open cover and check that juicing

components are installed and securely fastened. See Figure 3, Page 9.

5.

Close and lock all access covers.

There are 4 separate access covers: hopper cover, juicing components cover, cart
door (cover) and back cover.

NEVER

operate juicer unless all covers are in place.

6. Replace juice nozzle. Wet the o-ring before installing the nozzle.

7. Make sure juice reservoir is firmly in place.

8. Make sure juice reservoir valve is in closed position.

9.

Check the hopper for foreign objects.

Remove any foreign objects found in the hopper.

10. Make sure floor area around Juicer is clean and free of obstructions and water.

Wear appropriate non-slip footwear when water is necessary.

«
...
8
9
10
11
12
...
»

Содержание FRESH'N SQUEEZE

















































































Отзывы:

Нет отзывов

Похожие инструкции для FRESH'N SQUEEZE

Бренд: NASA electric Страницы: 17

ProJuicer JS700

Бренд: Campomatic Страницы: 14

Бренд: NUTRICHEF Страницы: 16

Бренд: Omega Страницы: 52

Бренд: Bourgini Страницы: 20

Бренд: decakila Страницы: 6

Бренд: Oceanic Страницы: 12

Бренд: Zelmer Страницы: 40

Бренд: Maestro Страницы: 40

Бренд: MAGIMIX Страницы: 64

Бренд: Omega Страницы: 116

Бренд: Wilfa Страницы: 64

Бренд: Wilfa Страницы: 64

Бренд: Gourmia Страницы: 14

Perfect Juicer PJ405

Бренд: Eldom Страницы: 24

Perfect Juicer PJ400

Бренд: Eldom Страницы: 30

Бренд: Eldom Страницы: 34

Perfect Juicer PJ600B

Бренд: Eldom Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды