16
FNS-0002-060-EN January 2017 Rev F
8.
Prepare cleaning solution.
JBT Corporation brand CorKlean is recommended, see Page 14.
Read the product label. Follow the manufacturer's mixing directions and safety
precautions.
9.
Immerse all components in cleaning solution.
Use the blunt end of plastic rod provided to displace any fruit material lodged in the
bore of the orifice tube.
Use pointed end of plastic rod to displace any fruit material lodged in cup fingers.
10. Scrub components.
Use a brush, towel, or sponge.
DO NOT
use abrasive pads such as steel wool.
Thoroughly rinse with clean water, then thoroughly rinse with sanitizer solution.
Follow the manufacturer's mixing directions and safety precautions.
11. For best results, soak strainer tube overnight.
After soaking overnight, rinse the strainer tube thoroughly before using. Check that all
strainer tube holes are clean. Clean strainer tube with a hard spray from a hose
while moving orifice tube back and forth in strainer tube. Rinse thoroughly with
sanitizer solution. Allow to air dry.
12. If possible, hose down juicing area and cover.
If location prohibits using a hose to clean juicing area and cover, ensure waste
container is in place. Wash down the exposed juicing area and cover with a sponge
or spray applicator using the recommended cleaning solution. Cover may be rinsed in
place or removed by lifting it off the hinges. Allow to stand for two minutes before
rinsing thoroughly with water.
13. Re-assemble juicing components.
Start by re-assembling strainer tube into juice manifold. Tighten with spanner wrench.
Insert orifice tube into bottom of strainer tube. Mount juice manifold assembly onto
locating pins with orifice tube notch engaging lower drive. Tighten spanner screw with
spanner wrench. Remove red protective cap from cutter. Install lower cup and tighten
spanner nuts with spanner wrench. Install upper cup by slipping pin into stem hole.
Install splatter shield.
Refer to Figure 6.
14. Verify that orifice tube is properly installed (Figure 7).
15. Remove wax build-up as needed.
Cups, hopper and other parts may acquire a build-up of wax over time.
a. Soak cups for five minutes in an ammonia cleaning solution.
Rinse thoroughly with sanitizer solution.
b. Wipe hopper and other parts with a cloth soaked in ammonia cleaning
solution.
Содержание FRESH'N SQUEEZE
