JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 15

Страница: 15 / 80

FNS-0002-060-EN January 2017 Rev F

DO NOT move or pull out splash guards.

Remove

juicing

components.

a. Cups should be separated. (Juicer should have been turned off with cups in the

separated position.)

b. Remove splatter shield by sliding upwards off mounting screws.

CAUTION:

NOT

PLACE

HANDS

FINGERS

BETWEEN

CUPS.

Grasp upper cup and pull out pin just above it. Place upper cup in waste

container.

Remove lower cup by removing spanner nuts on either side of lower cup.

(Spanner wrench is provided to loosen/tighten spanner nuts).

Place lower cup in waste container.

CAUTION: CUTTER AND KNIVES ARE SHARP.

Install red protective cap on cutter.

(Red protective cap is provided.)

Grasp juice manifold and orifice tube firmly. Remove entire juicing components
assembly.

Grasp orifice tube and pull out of strainer tube.

Remove strainer tube from inside juice manifold by turning tube counter-clockwise
and sliding out. (Spanner wrench is provided to loosen/tighten strainer tube.)

Place juicing components into waste container.

MOVING SPLASH GUARDS WHEN CLEANING CAN CAUSE SPLASH GUARDS
TO MISALIGN AND BREAK

DO NOT

PULL OUT

OR MOVE UPPER
SPLASH GUARD
WHEN CLEANING

DO NOT

PULL OUT

OR MOVE LOWER
SPLASH GUARD
WHEN CLEANING

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды