JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 38

Страница: 38 / 80

FNS-0002-060-EN January 2017 Rev F

Rebuilding (Continued)

Remove linear shafts.

With a 3/16" Allen wrench, loosen set screws at top and bottom of all three shafts.
Back screws out at least 1/4" to clear flats on shafts. If shafts are stuck, use bearing removal
puller with 3/8"-16 x 2" hex head cap screw to break free shafts.

Refer to Figure 25.

Lift out upper and lower drive arms with linkages still attached.

Disassemble rod end assemblies from drive and crank arms.

Note location and numbers of washers and spacers.

NOTE: Screws and rod ends on both crank arms are left hand threads.

10. Disassemble rod ends from links.

Reassemble with new rod ends (

Refer to Figures 26 and 27

), using rod end adjustment bar

with the appropriate rod and tooling washer. Remember one end is a left-handed thread.
Wrenches required - 3/4", 7/8", and 15/16".

Figure 25. Removal of Linear Shafts with Puller

Figure 26. Assembly of 5/8" Rod Ends

Figure 27. Assembly of 1/2" Rod Ends

Rod End Adjustment Bar

5/8" Tooling Washer

1/2" Tooling Washer

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды