JBT FRESH'N SQUEEZE Скачать руководство пользователя страница 5

Страница: 5 / 80

FNS-0002-060-EN January 2017 Rev F

Safety Labels

The safety labels shown below appear on the Juice Extractor. Safety labels provide essential
instructions on how to avoid possible hazards.

Please, for your safety:

FOLLOW THOSE INSTRUCTIONS AT ALL TIMES.

Should the Juicer safety labels become damaged or unreadable, contact JBT Corporation for
replacement labels.

Safety Instructions

Carefully review the following safety instructions.
Make them a habit when using the JBT Corporation Multi-Fruit Juicer.

If Juicer continues to run when any access cover is open, the interlock switch is defective.

Turn Juicer off immediately.

Call for service.

Prevent unauthorized access to Juicer by locking all covers with supplied key.

Prevent unauthorized operation of Juicer by placing electrical plug inside cart door.

4. NEVER

attempt to make any safety device inoperative.

5. NEVER

operate or perform maintenance or repair work on the Juicer when taking any kind of

drug or sedative, when under the influence of alcohol, or when fatigued.

6. ALWAYS

check adjustment of all nuts, bolts, and screws after installation, repair, or periodic

maintenance.

Содержание FRESH'N SQUEEZE

















































































Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды

JBT FRESH'N SQUEEZE, Руководство оператора и сервисное руководство

Результаты поиска

Содержание FRESH'N SQUEEZE

Отзывы:

Похожие инструкции для FRESH'N SQUEEZE

Бренды по названию

Популярные бренды