J&J Amusements Bumper Boat 2014 Скачать руководство пользователя

Страница: 123 / 168

3-35

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Remove the prop guard cover.

With a punch, carefully remove the roll pin from the

prop.

Pull the prop off of the shaft.

Remove the prop guard backing plate.

PROP AND GUARD

Reinstall the prop guard backing plate.

Slide the prop onto the shaft, taking care to line

up the prop holes with the corresponding holes on

the shaft.

Use an awl or suitable drift pin to help align the

holes.

Using a new, stainless steel roll pin, tap in with a

hammer and punch until it is flush with the prop.

Install the prop guard.

VISIT WWW.JJAMUSEMENTS.COM/TECHNICAL/INDEX.HTM FOR
TECHNICAL INFORMATION RELATED TO OUR PRODUCTS.

Содержание Bumper Boat 2014








































































































































































Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды