J&J Amusements Bumper Boat 2014 Скачать руководство пользователя

Страница: 26 / 168

0-26

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

BOAT ASSEMBLY

Lift the hull assembly and carefully place it inside the tube.

‹ CAUTION › The hull is heavy. Use two people when lifting

the hull assembly.

Make sure to grab the lip of the boat bottom when lifting the

assembly.

USE WORK GLOVES TO PROTECT HANDS FROM FIBER-

GLASS EDGES.

Rotate the boat hull inside of the tube so the air valve on the

tube is located at the back of the hull. This allows simple

maintenance to be performed from one direction on the bum-
per boat, as well as reducing the risks posed by guests access-

ing the valve.

This adapter makes it easy to fill your supertube and check pressure.
J&J # 2-60-A0006

SUPERTUBE PRESSURE TEST
ADAPTER AND FILLER

Содержание Bumper Boat 2014








































































































































































Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды