manualshive.com logo in svg

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Сервисное руководство для водных аттракционов Bumper Boat от компании J&J Amusements 2014 года доступно для бесплатного скачивания на manualshive.com. Получите подробные инструкции по обслуживанию и ремонту вашего аттракциона прямо сейчас. Уверенность в безопасности и долговечности вашего устройства.

Поделиться
Скачать
background image

0-7

 SPECIFICATIONS: ELECTRIC-POWERED

BLASTER BOAT.

DIMENSIONS:

Overall diameter .......................................................................................................................................72”(182 cm)
Overall height ...........................................................................................................................................40”(101 cm)
Wet weight .............................................................................................................................................488lbs(222kg)
Total battery weight ................................................................................................................................248lbs(113kg)
Super Tube II weight...................................................................................................................................23lbs(11kg)
Hull & deck weight ..................................................................................................................................139lbs(63kg)
Minimum water depth ....................................................................................................................................3ft(.91m)

MOTOR: 

Model.....................................................................................................................................................24v 1750 rpm
Type ......................................................................................Continuous duty 3/4 hp(1118w) 24v, permanent magnet
Motor weight ..............................................................................................................................................78lbs(36kg)
Cooling system ........................................................................................................................................................ Air
Maximum horsepower.......................................................................................................................3/4 hp(1750 rpm)
Maximum speed .............................................................................................................................. 3.5 mph(4.8 km/h)
Throttle........................................................................................................................Green rod / push button (on/off)
Squirt............................................................................................................................. Blue rod / push button (on/off)
Squirter Type .......................................................................................................................................24v submersible

BATTERY: 

Type ................................................................................................................................... 6 volt deep cycle (225 AH)
Weight ....................................................................................................................................................62 lbs (28 kg)
Length .................................................................................................................................................10 3/8(264 mm)

LOWER UNIT:

Gear ratio ................................................................................................................................................................1:1
Propeller......................................................................................................................3-7.2 x 4.7 in(3-184 x 120 mm)
Rotating direction ............................................................................................................Clockwise (viewed from rear)

Содержание Bumper Boat 2014









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bumper Boat 2014

BRIG FALCON F400 DELUXE User Manual preview
FALCON F400 DELUXE
Бренд: BRIG Страницы: 20
Barrus SHIRE 14 70 WB Manual preview
SHIRE 14 70 WB
Бренд: Barrus Страницы: 50
Malibu Boats 2000 Owner'S Manual preview
2000
Бренд: Malibu Boats Страницы: 60
Malibu Boats 2009 21 vRide Owner'S Manual preview
2009 21 vRide
Бренд: Malibu Boats Страницы: 132
Oxxean ALUMA 260 Owner'S Manual preview
ALUMA 260
Бренд: Oxxean Страницы: 37
Baja Outlaw 23 Owner'S Manual preview
Outlaw 23
Бренд: Baja Страницы: 82
Nortik Packraft FamilyRaft Assembling Instruction preview
Packraft FamilyRaft
Бренд: Nortik Страницы: 9
Nortik Scubi 1 Assembling Instruction preview
Scubi 1
Бренд: Nortik Страницы: 11
Nortik fold Assembly Instruction Manual preview
fold
Бренд: Nortik Страницы: 29
Baja Performance H2X Owner'S Manual preview
Performance H2X
Бренд: Baja Страницы: 83
Mercury Ocean Runner 300 Owner'S Manual preview
Ocean Runner 300
Бренд: Mercury Страницы: 40
Gumotex PULSAR User Manual preview
PULSAR
Бренд: Gumotex Страницы: 52
Jeanneau MERRY FISHER 855 Owner'S Manual preview
MERRY FISHER 855
Бренд: Jeanneau Страницы: 140
Malibu Boats Wakesetter 247 LSV Owner'S Manual preview
Wakesetter 247 LSV
Бренд: Malibu Boats Страницы: 170
Yamaha WaveRunner XL800 2001 Owner'S/Operator'S Manual preview
WaveRunner XL800 2001
Бренд: Yamaha Страницы: 136
Yamaha WaveRunner VX110 Sport Assembly Manual preview
WaveRunner VX110 Sport
Бренд: Yamaha Страницы: 26
Williams Turbojet J/T 285 Owner'S Handbook Manual preview
Turbojet J/T 285
Бренд: Williams Страницы: 23
Jilong Z-RAY I 200 Instruction Manual preview
Z-RAY I 200
Бренд: Jilong Страницы: 48

Бренды по названию

Популярные бренды

Загрузить еще бренды