J&J Amusements Bumper Boat 2014 Скачать руководство пользователя

Страница: 95 / 168

3-7

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

HANDLEBAR ASSEMBLY

The handlebar assembly has two parts and is mounted

on the motor with four 3/8” hex-head-mount bolts.

(Part # 2-10-0003 handlebar mount plate )

(Part # 2-10-0002 handlebar )

Remove the gear box

(see page 3-33).

Remove the hex-head motor-mount bolts.

After the bolts are removed, slide the plate up the drive

shaft housing.

Note

The drive shaft housing will be loose from the motor.

The handlebar is now free from the motor and can be

removed.

visit www.jjamusements.com and download a copy of our
complete accessory catalog!

Содержание Bumper Boat 2014








































































































































































Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды