J&J Amusements Bumper Boat 2014 Скачать руководство пользователя | Manualshive

Страница: 165 / 168

background image

7-3

GO

-KARTS

B

U

MPERBOAT

S

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

TM

CLEANING FADED OR OXIDIZED FIBERGLASS

There really isn’t any secret to cleaning faded or dull fiberglass; you just need some elbow grease and something to remove
the oxidation. The application varies for different products, but in general, you need to rub the surface with the oxidation
remover or polishing compound to remove the oxidized layer. You then let the product dry to a haze and buff it off to
reveal the clean (but not necessarily shiny) surface.

If your boat isn’t shiny at this point, it’s because the clean gelcoat surface is pitted and is dissipating the light instead of
reflecting it. By filling in the microscopic pits, you can restore the shine. To prove this, just apply some water to the surface
and see if it becomes shiny. If so, you then need to apply something which will fill in the pores and maintain the shine.

To use oxidation remover, first wet the gelcoat surface and apply the oxidation remover using a white Scotch-brite pad or
sponge. Rub the surface either until you see color in the pad or sponge (indicating you’ve rubbed off all the oxidation and
are now into the colored gelcoat), or until the surface no longer feels rough. At this point, you simply rinse off the surface
and wash away the oxidation residue.

«
...
163
164
165
166
167
...
»

Содержание Bumper Boat 2014









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Bumper Boat 2014

Бренд: Feathercraft Страницы: 23

Бренд: Feathercraft Страницы: 23

NeedleNose SUP NN116

Бренд: Sea Eagle Страницы: 13

Бренд: Scout Boats Страницы: 116

Бренд: Baja Страницы: 83

Beach Inshore 290 II

Бренд: Crivit Страницы: 34

Бренд: BENETEAU Страницы: 138

Бренд: Point 65 Страницы: 2

Бренд: Point 65 Страницы: 3

Бренд: Point 65 Страницы: 8

Бренд: Intex Страницы: 10

Бренд: Jeanneau Страницы: 92

Pike Inflatable Kayak

Бренд: NRS Страницы: 8

Бренд: Oru Kayak Страницы: 16

Dinghy Sportyak

Бренд: Sun Dolphin Страницы: 8

Mackinawl Mackinaw ss

Бренд: Sun Dolphin Страницы: 8

Бренд: Sun Dolphin Страницы: 12

Бренд: Swallow Boats Страницы: 22

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды