J&J Amusements Bumper Boat 2014 Скачать руководство пользователя

Страница: 31 / 168

0-31

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

BOAT LAUNCH PROCEDURE

Latch the dock ropes to the dock rails and the boat to secure

the boat to the dock rails. There should be two ropes and two

dock rails per boat.

Install the boat & dock rail hooks as described in the dock

rope installation on page 1-12.

Carefully move the boat to the edge of the pond.

NOTICE

Make sure to move the boat with the box lid underneath it to

prevent damage.

‹ CAUTION › This is a two-person job. Do not try to launch a

bumper boat with only one person.

Carefully slide the boat assembly (without the motor) into the

pond.

Inspect the boat and latch the boat hooks to the dock rails.

CHECK TUBE PRESSURE EASILY & ACCURATELY
WITH THE LOW-PRESSURE GAUGE #3-96-0024

Содержание Bumper Boat 2014








































































































































































Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды