J&J Amusements Bumper Boat 2014 Скачать руководство пользователя

Страница: 83 / 168

2-15

-KARTS

MPERBOAT

Specifications subject to change without notice - Check our website for valuable information including videos, workshop and operations manuals. www.jjamusements.com

503-304-8899

ENDURANCE CL

UTCH PLA

TES

Use a tire inflator to fill the tube.

VACUUM/BLOWER INFLATOR

Open the tube valve and cover it with an inflator hose.

Turn the blower on to fill.

Inflate the tube to the recommended 3 PSI.

Check it with a low-pressure gauge.

Before returning the boat to service, check the valve for

leaks by applying a solution of soapy water.

If bubbles form, valve needs to be tightened.

With the tube inflated, insert the valve tighter and turn the

nut 1/8th turn.

Re-check with the soapy water solution. Repeat as needed

until no bubbles form.

Содержание Bumper Boat 2014








































































































































































Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды

J&J Amusements Bumper Boat 2014, Руководство по обслуживанию

Результаты поиска

Содержание Bumper Boat 2014

Отзывы:

Похожие инструкции для Bumper Boat 2014

Бренды по названию

Популярные бренды