Jacobsen LF550-H-T4F Скачать руководство пользователя страница 54 | Manualshive

Страница: 54 / 88

background image

9 MAINTENANCE

53

9.8

BATTERY ________________________________________________________________

Before you service the battery, make sure the ignition switch is in the OFF position and the key is removed.

Tighten the battery cables on the battery terminals, To prevent corrosion,
apply a layer of silicone dielectric grease to battery terminals and ends of
cables. Keep the vent caps and battery terminal covers in position.

Before you do any welding operation on the mower, always disconnect the
battery cables from the battery and the connectors from the controllers.

Confirm the battery polarity before you connect or you disconnect the
battery cables.

When you install the battery, always connect the positive (RED) battery cable before the negative (BLACK) battery
cable.

When you remove the battery, always disconnect the negative (BLACK) battery cable before the positive (RED) battery
cable.

Jump-Starting the Mower

a

Before you try to jump-start the mower, check the condition of the drained battery.

b

Connect the positive (+) battery terminal of the charged battery to positive battery terminal of the drained battery.

c

Connect the negative (–) battery terminal of the charged battery to frame of vehicle with the drained battery.

d

When the cables are connected, start the engine on the vehicle with the good battery, then start the mower.

CAUTION

When you service the battery, always use the tools with insulation, wear protective glasses and protective clothing.

Discard used batteries as shown in your local regulations.

WARNING

The battery contains corrosive acid. Prevent contact with the battery acid.

Always wash your hands after you service a battery.

WARNING

The battery posts, battery terminals and related accessories contain lead and lead compounds, chemicals known to
the State of California to cause cancer and other reproductive harm.

WARNING

The battery can release hydrogen gas that is explosive. To decrease the risk of an explosion, prevent sparks near
the battery. Always connect the negative jumper cable to the frame of the mower with the drained battery.

!

!

!

Pb

!

«
...
52
53
54
55
56
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Sabre Страницы: 9

911394 - Pro 21SCH

Бренд: Gravely Страницы: 23

Бренд: Worx Nitro Страницы: 75

Бренд: Hayter Страницы: 26

Бренд: Mowox Страницы: 219

Бренд: MTD Страницы: 31

Бренд: Simplicity Страницы: 80

Бренд: Bad Boy Страницы: 36

Бренд: Cub Cadet Страницы: 44

Бренд: Cub Cadet Страницы: 32

Бренд: Craftsman Страницы: 24

Бренд: Craftsman Страницы: 32

Бренд: Craftsman Страницы: 93

Бренд: Craftsman Страницы: 100

Бренд: Craftsman Страницы: 25

Бренд: Craftsman Страницы: 112

Бренд: Craftsman Страницы: 116

Бренд: Craftsman Страницы: 120

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды