Jacobsen LF550-H-T4F Скачать руководство пользователя | Manualshive

Страница: 15 / 88

background image

SPECIFICATIONS 4

14

4.5

VIBRATION LEVEL_________________________________________________________

The mower was tested for hand and arm vibration levels. The operator was in the normal position to drive the vehicle,
with two hands on the steering mechanism. The engine was in operation and the cutting device was in rotation, while
the mower was not moving.

The Machinery Safety Directive 2006/42/EC

By compliance to:

The Lawnmower Standard BS EN ISO 5395-3

Referenced to Hand/Arm: BS EN ISO 20643:2008

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Hand/Arm Standards: BS EN ISO 5349-1 (2001)

BS EN ISO 5349-2 (2001)

The mower was tested for Whole Body vibration levels. The operator was in the normal position to drive the vehicle,
with two hands on the steering mechanism. The cutting device was in rotation with the mower driven in a straight line
at 6 Km/hr on a level and cut lawn.

The Machinery Safety Directive 2006/42/EC

By compliance to:

Whole Body EN1032:2003

Information Supplied for Physical Agents Directive 2002/44/EC

By reference to:

Whole Body Standards BS EN ISO 2631-1 (1997)

LF550-H / LF570-H

LF550 / LF570

Hand/Arm

Acceleration Level

68011, 68012 LF550-H / 68013, 68014 LF570-H

68015, 68012 LF550 / 68017, 68018 LF570

Maximum Left Hand or Right Hand Accelerations m/s

2

Mean Value of X, Y, Z Aeq

LF550-H 68011, 68012

TBD ± 0.6

LF570-H 68013, 68014

TBD ± 0.6

LF550 68015, 68016

0.7958 ± 0.6

LF570 68017, 68018

1.50 ± 0.6

LF550-H / LF570-H

LF550 / LF570

Whole Body

Acceleration Level

68011, 68012 LF550-H / 68013, 68014 LF570-H

68015, 68012 LF550 / 68017, 68018 LF570

Maximum Seat Pad Accelerations m/s

2

Mean Value of X, Y, Z Aeq

LF550-H 68011, 68012

TBD ± 0.056

LF570-H 68013, 68014

TBD ± 0.056

LF550 68015, 68016

0.295 ± 0.056

LF570 68017, 68018

0.323 ± 0.056

«
...
13
14
15
16
17
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Yard Machines Страницы: 32

YP21KH42 (96041031300)

Бренд: Yard Pro Страницы: 20

Бренд: Greencut Страницы: 68

Бренд: Poulan Pro Страницы: 44

Бренд: Cub Cadet Страницы: 44

Бренд: Alamo Страницы: 168

Craftsman 917.250262

Бренд: Sears Страницы: 60

Бренд: Texas Страницы: 60

Бренд: Agri-Fab Страницы: 24

COLLECTOR 53 SE COMBI 53 SE COMBI

Бренд: Stiga Страницы: 2

Бренд: Yard-Man Страницы: 11

Бренд: Oleo-Mac Страницы: 332

Бренд: Gardenline Страницы: 24

Бренд: Flymo Страницы: 11

Z Master Professional 7500-D Series

Бренд: Toro Страницы: 80

Бренд: Toro Страницы: 60

Бренд: Aerotek Страницы: 18

Бренд: Gtech Страницы: 32

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды