Jacobsen LF550-H-T4F Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 88

background image

INTRODUCTION 2

2

2Introduction

2.1

IMPORTANT ______________________________________________________________

The Jacobsen LF550 / LF570 with a Diesel engine is a self propelled fairway mower. The hydraulic systems are for the
traction drive, steering, lift - lower and the cutting unit drive.

If you follow all instructions in this manual, you increase the life of your mower and keep its maximum performance.
Adjustments and maintenance must always be done by an approved technician.

IMPORTANT: Do the maintenance included in this manual to make sure that the quality of cut is kept at a high level.

This SAFETY, OPERATION AND MAINTENANCE MANUAL is part of the mower and must stay with the mower
always. Suppliers of both original and used mowers need to keep the documentation that comes with the mower.

You must use the mower to cut the grass and not for any other purpose. Compliance with the conditions or operation,
service and repair specified by the manufacturer, are understood to be part of the correct use.

ALL operators MUST read through this manual and understand the Safety Instructions, controls, lubrication and
maintenance procedures.

Make sure that you obey all safety and road traffic regulations.

You must not make any changes to the mower that the manufacturer does not approve. This type of change can
release the manufacturer from the liability for any damage or injury.

When you discard worn parts, know the environmental result and use the systems available in the country where the
mower is used. When the mower is at its end of life, there are guidelines in this manual for the removal of the mower
from use.

Use only Jacobsen approved parts.

2006/42/EC

The instructions recorded here are the original instructions confirmed by Jacobsen, A Textron Company.

«
1
2
3
4
5
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Gardena Страницы: 52

Бренд: White Страницы: 20

Бренд: Yard Pro Страницы: 108

Бренд: Troy-Bilt Страницы: 40

Бренд: Gardeo Страницы: 60

Eco Wheeler GM 413.2 R

Бренд: Garten Meister Страницы: 96

Бренд: Lastec Страницы: 88

Бренд: Brill Страницы: 96

Бренд: Agway Страницы: 32

Бренд: Ariens Страницы: 77

Бренд: Ariens Страницы: 69

Бренд: Poulan Pro Страницы: 48

GRO20V20WIFI-2A

Бренд: GARDEO PRO Страницы: 158

Бренд: Giant-Vac Страницы: 32

Бренд: EINHELL Страницы: 20

Бренд: EINHELL Страницы: 60

Бренд: EINHELL Страницы: 60

Бренд: EINHELL Страницы: 60

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды