Jacobsen LF550-H-T4F Скачать руководство пользователя

Страница: 22 / 88

5 DECALS

5Decals

5.1

SAFETY DECALS _________________________________________________________

Understand the purpose of these decals. The decals are important to the safe operation of the mower. REPLACE THE
DAMAGED DECALS IMMEDIATELY.

DANGER

To prevent injury while you do work on the battery:

Connect the negative (BLACK) wire after the positive (RED)
wire. Remove the negative (BLACK) wire before the positive
(RED) wire.

Keep sparks and flames away from the battery. Prevent the
contact with the battery acid.

To prevent injury while you attach the jumper cables to the battery:

Connect the positive (+) battery terminal of the charged
battery to positive battery terminal of drained battery.

Connect the negative (–) battery terminal of the charged
battery to frame of vehicle with drained

battery.

WARNING

The engine coolant is under pressure. To prevent injury, do not remove the
radiator cap on a hot radiator.

WARNING

To prevent injury, do not touch the muffler or
muffler shield. The muffler temperatures can be
more than 150° F (66° C).

WARNING

Always use the seat belt with the ROPS frame in the vertical and
locked position.

Never use the seat belt with the ROPS in the folded position.

4181864

4181862

4199140

Содержание LF550-H-T4F

























































































Результаты поиска

Содержание LF550-H-T4F

Отзывы:

Похожие инструкции для LF550-H-T4F

Бренды по названию

Популярные бренды

Jacobsen LF550-H-T4F, Руководство по безопасности, эксплуатации и техническому обслуживанию

Результаты поиска

Содержание LF550-H-T4F

Отзывы:

Похожие инструкции для LF550-H-T4F

Бренды по названию

Популярные бренды