Jacobsen LF550-H-T4F Скачать руководство пользователя страница 64 | Manualshive

Страница: 64 / 88

background image

9 MAINTENANCE

63

9.20 ELECTRICAL SYSTEM

____________________________________________________________

General precautions to decrease electrical problems are -

•

Make sure that all the connections are clean and correctly fastened.

•

Check the interlock system, fuses and circuit breakers at normal intervals. If the interlock system does not
operate correctly and you can not correct the problem, contact an authorized Jacobsen Dealer.

•

Keep the wiring harness away from hot surfaces and moving parts.

•

Make sure the seat switch wiring harness is connected to the mower wiring harness.

•

Check the battery and the alternator.

•

Do not wash or pressure spray around electrical connections and components.

The electrical system is monitored and controlled by the controller found behind the operator compartment. The
controller has 28 light emitting diodes (LED) that can help to correct electrical system problems.

A circuit breaker, six fuses and three relays found on or near the controller are used to protect the mower circuits.

CAUTION

Always turn the ignition switch to the off position and remove the negative (BLACK) battery cable before you inspect
or service the electrical system.

NOTICE

For factory help with controller problems, give the hardware revision and software version found on the controller.
The replacement controllers with higher revision levels will be compatible.

!

2-1 RAISE SOL
2-2 MOW SOL
2-3 BACKLAP SP;
2-4 LOWER SOL
2-5 GLOW RELAY
2-6 START RELAY
2-10 FUEL SOL HOLD
3-1 FUEL SOL PULL
2-9 BRAKE SOL
2-12 SPARE
3-9 EDC SOL
3-10 EDC SOL

2-11 SPARE
3-2 ENG TEMP
3-7 TRACTION
1-1 SEAT SW
1-2 SPARE
1-3 BACKLAP SW
1-12 REEL LVL SW
1-4 HYD OIL LVL SW
1-9 HYD FILTER SW
1-10 ENG OIL SW
2-7 ALTERNATOR
1-5 PRGM SEL 1
1-6 PRGM SEL 2
1-11 PRGM SEL 3
COMM STATUS
POWER STATUS

FUSES
20 AMPS MAX
POWER INPUT 1
POWER INPUT 2

OUTPUTS

INPUTS

J1

J2

J3

20

20

F6

F7

F1

CB1

F2

F3

F4

J

A

COBSEN 4270813

MTI500819

REV X2

D

A

TE YYWW

SOFTW

A

RE

9585$

RoHS

Compliant

CR1

CR3

CR2

5

5

25

10

CB1 - 50 Amp Circuit Breaker

CR1 - Main Relay
CR2 - Glow Plug Relay
CR3 - Starter Relay

F1 - 10 Amp Fuse - ECU +12V
F2 - 25 Amp Fuse - Main Relay
F3 - 5 Amp Fuse - ECU Start
F4 - 5 Amp Fuse - EGR
F6 - 20 Amp Fuse - Ignition
F7 - 20 Amp Fuse - Lights

Software
Version

Hardware
Revision

«
...
62
63
64
65
66
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Lawn-Boy Страницы: 84

532 43 41-99 Rev. 1

Бренд: McCulloch Страницы: 72

Бренд: MTD Страницы: 16

Бренд: Garland Страницы: 64

Бренд: Yard-Man Страницы: 16

Бренд: Oleo-Mac Страницы: 292

Бренд: Snapper Страницы: 18

Бренд: Bestgreen Страницы: 20

Бренд: Honda Страницы: 81

Бренд: Craftsman Страницы: 68

Бренд: EMAK Страницы: 120

Бренд: Gardena Страницы: 152

Бренд: EMAK Страницы: 265

Бренд: Simplicity Страницы: 56

Бренд: Simplicity Страницы: 20

Бренд: Venture Products Страницы: 35

Бренд: Texas A/S Страницы: 80

Бренд: Simplicity Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды