Jacobsen LF550-H-T4F Скачать руководство пользователя | Manualshive

Страница: 28 / 88

background image

6 CONTROLS

27

6.2.1 IGNITION SWITCH _________________________________________________________

The ignition switch has three positions, OFF, RUN and START. In the RUN
position, the controller program is active and input and output circuits are
monitored.

6.2.2 PARKING BRAKE SWITCH__________________________________________________

To engage the parking brake, press the front of the switch. Parking brake light on LDU (See
6.2.9) will turn on. Operation of the cutting units operation is disabled with the parking brake
engaged.

To disengage parking brake, press the rear part the switch. The parking brake light will turn off.

NOTE: Engine will not start with the parking brake switch in the OFF position.

6.2.3 CRUISE CONTROL SWITCH_________________________________________________

The cruise control switch controls the operation of the cruise control system.

To engage the cruise control, press the traction pedal, push the orange lock forward and press
the front of the switch.

To disengage the cruise control, press the rear part of the cruise control switch, press the rear
part of the parking brake switch or turn the ignition switch to the OFF position.

OFF

RUN

START

«
...
26
27
28
29
30
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Jacobsen Страницы: 46

Бренд: Jacobsen Страницы: 70

Бренд: Jacobsen Страницы: 26

Бренд: Jacobsen Страницы: 247

Greens King V Plus

Бренд: Jacobsen Страницы: 94

Groom Master II

Бренд: Jacobsen Страницы: 104

Бренд: Jacobsen Страницы: 144

Бренд: MTD Страницы: 12

69168 - Turfcat T628D

Бренд: Jacobsen Страницы: 59

Бренд: Ransomes Страницы: 116

Бренд: Yard-Man Страницы: 20

Бренд: Yazoo Страницы: 24

Бренд: Racing Страницы: 29

Бренд: Snapper Страницы: 56

Бренд: Flymo Страницы: 11

Z Master Professional 7500-D Series

Бренд: Toro Страницы: 80

Бренд: Bad Boy Страницы: 36

Бренд: Hurricane Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды