Jacobsen LF550-H-T4F Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 88

background image

CONTROLS 6

34

6.4

TRACTION PEDAL _________________________________________________________

The traction pedal controls the movement of the mower. Press the
front of the pedal to move in the forward direction. Press the rear
part of the pedal to move in the reverse direction. When traction
pedal is not pressed, the pedal will return to the NEUTRAL position.

6.5

STEERING WHEEL TILT ADJUSTMENT _______________________________________

The steering wheel angle is adjustable. Lift the lever and move the steering wheel backward or
forward to get the correct setting. Release the lever to set the position of the steering wheel.

6.6

SEAT CONTROLS _________________________________________________________

The seat has two controls to adjust for the operator.

Lift the seat position lever and move the seat backward or forward.
Release the lever to set the adjustment. Make sure the seat is
locked in position before you operate the mower.

Rotate the knob to the correct position for the weight of the
operator.

CAUTION

To prevent injuries, DO NOT adjust the steering wheel while you operate the mower. Only
adjust the steering wheel with the mower stopped and the parking brake engaged.

WARNING

To prevent injuries, DO NOT adjust the seat while you operate
the mower. Only adjust the seat with the mower stopped and
parking brake engaged.

Forward

Reverse

!

Seat Position
Lever

Weight Adjust
Knob

!

«
...
33
34
35
36
37
...
»

Содержание LF550-H-T4F

























































































Отзывы:

Нет отзывов

Похожие инструкции для LF550-H-T4F

Бренд: Yard force Страницы: 25

Бренд: Exmark Страницы: 4

Бренд: Worx Страницы: 44

Бренд: Troy-Bilt Страницы: 40

Бренд: Yazoo Страницы: 8

Бренд: Coopers of Stortford Страницы: 13

Бренд: Wards Garden Mark Страницы: 4

Бренд: Wards Garden Mark Страницы: 16

Бренд: Craftsman Страницы: 44

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 48

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 52

Бренд: Craftsman Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды