ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 50

Страница: 50 / 51

Stuffing box gland packing (210) - one set for four gland halves.

d) Stuffing box gland halves (107) - four required.

With these parts on hand, pump can be easily and quickly reconditioned by replacing the worn
parts.

An alternate, though not as desirable as that stated above, is to have on hand parts that are most
likely to wear and which can be used as needed.

Following is a list of these suggested parts:

a) Stuffing box packing (106) - one set for two stuffing boxes.

b) Stuffing box gland packing (210) - one set for four gland halves.

Shaft sleeve (104 and 126) - one each.

d) Ball bearings (112 and 137) - one of each.

e) Shaft nut (110) - one required.

Wearing rings (103) - two required; or (127 and 142) two of each.

g) Diaphragm (146) - one required.

h) Shaft (122) - one required.

Impeller key (178) - one required.

Stuffing box bushings (125) - two required.

Stuffing box gland halves (107) - four required.

If it is not convenient or desirable to carry the spare parts listed in items 1 or 2, the following list is
suggested as a minimum for servicing the pump under ordinary conditions of wear:

a) Stuffing box packing (106) - one set for two stuffing boxes.

b) Stuffing box gland packing (210) - one set for four gland halves.

Shaft sleeves (104 and 126) - one each.

d) Ball bearings (112 and 137) - one of each.

e) Shaft nut (110) - one required.

7.15 Instructions for ordering spare parts

Repair orders will be handled with the minimum of delay if the following directions are followed:

Give Model No., size of the pump and serial number. These can all be obtained from the name
plate.

Write plainly the names, part numbers and material of the parts required. These names and num-
bers should agree with those on the

7.6 Sectional View on page 34

Give the number of parts required.

Give complete shipping instructions.

For more information, call your nearest Goulds sales representative or visit our website at

http://

www.gouldspumps.com

7.15 Instructions for ordering spare parts

3316 Installation, Operation and Maintenance Instructions

Содержание GOULDS PUMPS 3316




















































Результаты поиска

Содержание GOULDS PUMPS 3316

Отзывы:

Похожие инструкции для GOULDS PUMPS 3316

Бренды по названию

Популярные бренды

ITT GOULDS PUMPS 3316, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание GOULDS PUMPS 3316

Отзывы:

Похожие инструкции для GOULDS PUMPS 3316

Бренды по названию

Популярные бренды