ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 51

background image

applied evenly to the circumference of the outer race of the bearing. A steady pressure must be ap-
plied to the puller screw.

Figure 19:

NOTICE:

Never use hammer blows to drive shaft through bearings.

Protect bearings from dirt or other contamination.

14. Slide bearing housings from shaft. Remove deflectors (123) from both ends of shaft.
15. Slip casing wearing rings (103 or 127) from impeller and off rotating element.
16. Slide packing, lantern rings (105) and stuffing box bushings (125) off ends of shaft.
17. Smooth the exposed portions of the shaft at the ends of the sleeves with fine emery cloth so that

sleeves will not bind while being removed.

18. The shaft sleeve (126) must be removed first. This is the sleeve with the spanner holes and set

screw. Loosen set screw. Using a pin spanner or strap wrench unscrew sleeve by turning it counter-
clockwise. Do not use pipe wrench. Never attempt to remove the sleeve (104) which has no span-
ner holes until impeller and impeller key are removed from shaft.

19. Tap the impellers (101) and (145), with diaphragm (146) in place, from shaft with a lead mall. Tap

evenly around the impeller as near as possible to the shaft. Do not drive against the sealing surface
on end of hub. Do not let the key "ride up" on the exposed curved portion of the sled runner keyway.
Should the impeller key start to "ride" as the impeller is being removed, the key can be driven back
by a drift pin or piece of keystock a size smaller than the impeller key.

20. Remove key from keyway.
21. Unscrew and remove the remaining sleeve from shaft by hand or with a strap wrench. Turn in a

counter-clockwise direction. This completes the disassembly of the pump.

7.5 Dismantling of pump

3316 Installation, Operation and Maintenance Instructions

33

«
...
33
34
35
36
37
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Eaton Страницы: 2

Бренд: Salamander Pumps Страницы: 32

Бренд: A.O. Smith Страницы: 77

Бренд: Samoa Страницы: 32

Бренд: JAMA Страницы: 55

Бренд: OilGear Страницы: 28

Бренд: Jandy Страницы: 108

Бренд: Magnum Страницы: 16

Бренд: T-MAG Страницы: 36

Бренд: Waters Страницы: 116

Water Solutions 3098 Series

Бренд: Zoeller Страницы: 4

Aquanot Spin 508

Бренд: Zoeller Страницы: 2

Бренд: Zoeller Страницы: 11

Бренд: Zip Страницы: 18

Бренд: Vagner Pool Страницы: 35

Бренд: A.O. Smith Страницы: 4

Бренд: Takagi Страницы: 27

Бренд: Rowi Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды