ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 34 | Manualshive

Страница: 34 / 51

background image

6.

Install stuffing box packing as described in Stuffing boxes.

7.5 Dismantling of pump

Figure 18:

1.

Drain liquid from pump.

2.

Shut off and disconnect any auxiliary piping.

3.

Disconnect coupling.

4.

Remove gland assembly from stuffing boxes.

5.

Jack and remove dowel pins from upper half casing by use of hex nut provided on top of pins. Re-
move nuts from casing parting studs and loosen upper half casing (100) by screwing two bolts
(½"-13 threads) in holes provided in the flange. Lift off upper half casing, being careful not to injure
the parting gasket. Use the lugs or eye bolts provided for lifting the upper half casing. Do not use
these lugs or eye bolts for lifting entire pump.

6.

Remove nuts from bearing cap studs and lift bearing cap (111) from unit.

NOTICE:

These caps must be replaced on the same end of pump from which they were removed. They
should be marked for identification before disassembly.

7.

Carefully lift rotating assembly from unit and place on padded supports which will not injure the
shaft sleeves.

8.

Note the distance from the end of the shaft to the face of the pump half coupling so that the cou-
pling half can be correctly positioned when reassembled. Pull the coupling half from pump shaft.

9.

Remove coupling key.

10. Remove constant level oilers (251) on both thrust end and coupling end. Drain oil from bearing

housings (134 and 166).

11. Remove cap screws from each end cover and remove end covers (109 and 119) from bearing

housings (134 and 166). Preserve end cover gaskets (360 and 360A).

12. Unscrew shaft nut (110) from shaft.
13. Remove ball bearings (112 and 137) from shaft seat by use of a bearing puller. Details of a recom-

mended puller, capable of removing bearings from all three groups of pumps are shown in

. Care must be used. Puller bar must be square with shaft so that equal pressure is

7.5 Dismantling of pump

32

3316 Installation, Operation and Maintenance Instructions

«
...
32
33
34
35
36
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

FCD-JTHMG80-III

Бренд: Haier Страницы: 2

Little Sea-ox FCD-JTHC40-III (E)

Бренд: Haier Страницы: 6

Бренд: Haier Страницы: 18

Бренд: Haier Страницы: 23

Бренд: Haier Страницы: 20

Бренд: Haier Страницы: 2

Бренд: Badu Tec Страницы: 98

Бренд: ULTIMATE SPEED Страницы: 52

Бренд: Wayne Страницы: 8

Бренд: Wayne Страницы: 20

Бренд: Wayne Страницы: 8

Бренд: Wayne Страницы: 12

Бренд: Takagi Страницы: 27

Бренд: Airetool Страницы: 20

Бренд: Daikin Страницы: 40

Бренд: Vallfirest Страницы: 32

Бренд: Dimplex Страницы: 64

Бренд: Alto Страницы: 17

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды