ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 51

background image

3.6 Installation and connection of bearing cooling water piping

Bearing cooling coils are supplied when ordered. Bearings should be cooled when the liquid pumped is:

Between 250° and 350°F, in addition to gland quenching.

The cooling coils are installed as follows:

1.

Refer to

7.6 Sectional View on page 34

which shows the installed cooling coil.

2.

Special fittings and tubing are in the box of fittings sent with the pump.

3.

Remove four - ¼" plugs from bearing end covers (109 and 119) - one plug from each side of each
cover. The plugged openings are those below the openings for the constant level oilers.

4.

Screw ¼" pipe x ¼" OD tube compression fittings into each of the four openings.

5.

Push each ¼" OD x 9" long copper tube through one fitting until it comes out the fitting on the other
side. Center tubing so that equal lengths project from each side. Tighten nuts on compression fit-
tings.

6.

Connect the ¼" pipe x ¼" OD tubing elbow to each end of the copper tube. This provides a ¼" pipe
connection for cooling water piping.

7.

Connect cooling water. The inlet line should have a shutoff valve to regulate flow.

3.7 Connection of drain piping

Connect overflow outlets from stuffing boxes (located in casing near pump feet) to drain, and connect
overflow from bedplate (located at pump end of bedplate) to drain. All of the above overflow openings
are tapped for ¾" pipe.

3.6 Installation and connection of bearing cooling water piping

3316 Installation, Operation and Maintenance Instructions

21

«
...
21
22
23
24
25
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Haier Страницы: 2

Бренд: Calpeda Страницы: 80

Бренд: Kärcher Страницы: 18

Бренд: SAER Elettropompe Страницы: 36

Naviels UKDAX-10EDT

Бренд: DAXOM Страницы: 28

Бренд: Sanden Страницы: 32

Бренд: DAB Страницы: 184

Бренд: DAB Страницы: 184

Бренд: AquaStar Страницы: 28

Бренд: Dux Страницы: 20

Бренд: Oasis Aquatics Страницы: 14

Summit Pumper Vacuum

Бренд: Alto Страницы: 6

Бренд: LEYBOLD Страницы: 34

Бренд: AMAZON COMMERCIAL Страницы: 48

Бренд: KSB Страницы: 20

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренд: Parkside Страницы: 122

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды