ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 51

background image

Figure 16:

4.

Priming by Automatic Primer Pump, See

Figure 17: on page 25

Figure 17:

Where there is a fluctuating suction lift that occasionally might drop below the normal limits of the
pump or for installations where there is any quantity of air entrained with the liquid being pumped,
the system shown in

Figure 17: on page 25

is very well adapted.

A vacuum tank and a vacuum gauge can be installed near the primer pump and the vacuum switch
set to automatically start or stop the primer pump according to the vacuum required to keep the sys-
tem primed.

4.2 Regulation of cooling water flow

The supply of liquid to the water-cooled bearings and quenching glands should be regulated by valves in
the supply line. Approximately ½ G.P.M. to each gland and 1 G.P.M. to each bearing cooling coil is suffi-
cient. The cooling lines should be checked periodically to see that they have not become clogged.

4.2 Regulation of cooling water flow

3316 Installation, Operation and Maintenance Instructions

25

«
...
25
26
27
28
29
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Ace Страницы: 13

Бренд: Davey Страницы: 28

Бренд: Radiant Страницы: 8

Бренд: Waters Страницы: 116

Бренд: Naked Страницы: 12

Бренд: Zoeller Страницы: 16

Бренд: STIEBEL ELTRON Страницы: 15

Бренд: IWAKI PUMPS Страницы: 32

RIBILAND PRPVC1501V

Бренд: Ribimex Страницы: 35

Бренд: AMAZON COMMERCIAL Страницы: 48

Бренд: INOXPA Страницы: 19

S-THERM+ SHP-140ERC

Бренд: Sinclair Страницы: 18

DUSTTRAK 8530EP

Бренд: TSI Instruments Страницы: 2

Бренд: Hubbell Страницы: 27

Бренд: Reliable Страницы: 18

1 EPBH 9.2-11 T-AVS

Бренд: EBARA Страницы: 16

Бренд: DAB Страницы: 708

Бренд: hajdu Страницы: 65

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды