ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 21 | Manualshive

Страница: 21 / 51

background image

b) When installing the packing and the PTFE lantern ring, twist the rings sideways just enough to

get them around the shaft sleeves.

Do not attempt to pull rings straight out to get them over shaft and shaft sleeve. See

.

Figure 9:

c)

Insert lantern ring (105) against stuffing box bushing (125) (2 pieces make one ring).

NOTICE:

Notches must face one another but need not be aligned.

Figure 10: Lantern rings

d) Then insert five rings of packing for Group "S" and "M" pumps and six rings for Group "L"

pumps, staggering the joints. See sectional assembly,

7.3 Sectional view on page 31

ring should be firmly seated before the next ring is added. Two extra rings of packing are fur-
nished in each set of packing. The extra ring for each side may be added as required.

e) Insert gland packing (210) into recess in each gland half and trim off excess flush with face of

each gland half.

f)

Run ½"-13 UNC nuts (355) about threefourths the length of the threaded part of bolts (353) and
place cupped washers (354) on gland bolts. (See

Figure 11: on page 20

g) Insert lower half gland (107) into stuffing box.

h) Insert round, flattened end of gland bolts into recess of bearing housing (134 or 166). Gland

bolts do not screw into tapped holes in casing. Tapped holes in casing are for mechanical seal
gland only when pumps are furnished with seals. Threaded portion of gland bolt lays on gland
half.

3.3 Stuffing boxes

3316 Installation, Operation and Maintenance Instructions

19

«
...
19
20
21
22
23
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Danfoss Страницы: 38

Бренд: Navien Страницы: 48

Бренд: Navien Страницы: 2

Бренд: A.O. Smith Страницы: 2

PacificHydrostar 2" Gasoline Powered Clear Water...

Бренд: Pacific hydrostar Страницы: 24

Бренд: Cordivari Страницы: 44

Бренд: Tiger Страницы: 36

EZH2O LZWS-LRPBM28K

Бренд: Elkay Страницы: 4

SMOOTHFLO Series

Бренд: Remco Страницы: 2

Бренд: Wacker Neuson Страницы: 42

Бренд: T.I.P. Страницы: 134

Бренд: MARNEX Страницы: 28

LARIUS VEGA 5:1

Бренд: Samoa Страницы: 28

Бренд: Seisco Страницы: 20

Бренд: Wayne Страницы: 4

Little Giant PES-70

Бренд: Franklin Electric Страницы: 2

Бренд: Rinnai Страницы: 66

Бренд: Jandy Страницы: 96

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды