ITT GOULDS PUMPS 3316 Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 51

background image

Figure 13:

Close discharge gate valve, open 1st stage vent valve and open valve "S" in priming supply line
until all air is expelled and water issues from vent opening. Close valve "S", close 1st stage air vent
valve and start pump; then open discharge gate valve.

b) By Separate Hand or Manually Controlled Priming Pump (See

Figure 14: on page 23

Figure 14:

Close discharge gate valve (keep 1st stage air vent valves closed) and open 2nd stage air vent
valve (valve "S") in line to priming pump. Exhaust air from pump and suction piping until water flows
from priming pump. Close valve "S", start pump and open discharge gate valve.

By reversing connections on priming pump and extending priming pump suction to source of liquid
supply, centrifugal pump may be primed by pumping liquid into casing until liquid comes out of the
open 1st stage air vent valve.

In either of these methods (a) and (b), the pump will remain primed, provided foot valve is tight. Any
failure, however, of foot valve when pump is standing idle, will permit the pump to lose its prime.
During long idle periods, the pump can also lose its prime through leakage from stuffing boxes.

4.1 Priming

3316 Installation, Operation and Maintenance Instructions

23

«
...
23
24
25
26
27
...
»

Содержание GOULDS PUMPS 3316




















































Отзывы:

Нет отзывов

Похожие инструкции для GOULDS PUMPS 3316

Бренд: Barnes Страницы: 12

Бренд: Haier Страницы: 2

Бренд: Macnaught Страницы: 12

Бренд: A.O. Smith Страницы: 2

Бренд: Wangen Страницы: 72

Бренд: vacuubrand Страницы: 24

VRV EMERION RXYQ-AATJA

Бренд: Daikin Страницы: 429

Бренд: A.O. Smith Страницы: 4

Бренд: ICI Caldaie Страницы: 48

HydroTap All-In-One BC 60/85A

Бренд: Zip Страницы: 24

Бренд: Calpeda Страницы: 5

Бренд: Rheem Страницы: 47

Бренд: Quantum Страницы: 36

Бренд: All-Flo Страницы: 28

Бренд: Carlisle Страницы: 24

Бренд: Realax Страницы: 60

Hydra-Cell G-25

Бренд: Wanner Engineering Страницы: 20

WSAN-XSC3 MF 200.4

Бренд: CLIVET Страницы: 68

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды